開票另加稅點,詳情諮詢客服!
Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller
Features:
Pixhawk 2.4.8 support the latest official ardupilot firmware and PX4 firmware.
1. The advanced 32-bit ARM CortexM4 high-performance processors(2MB flash), can run NuttX RTOS real-time operating system;
2. 14 PWM / servo output;
3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes;
6. Provide redundant power input and failover;
7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface
9. Micro SD recording flight data;
Specifications:
Interface
1.5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
915MHZ 100MW Radio telemetry V5+PX4FLOW:
PIXHAWK 2.4.8+4G TF Card+Safety Button+Buzzer
PPM Encoder+I2C Board+RGB Led+Wire+M8N GPS
PX4FLOW 915MHZ 100MW Radio telemetry V5
Power Module :
For PIXHAWK 2.4.8 :used for PIXHAWK2.4.8 AND APM2.8 Flight Control
For PIXHAWK PRO :used for PIXHAWK PRO Flight Control
For PIXHAWK 6C :used for PIXHAWK 6C Flight Control
Description:
This Power Module PRO provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, along with shrink tubing on the PCBA for physical protection.
Specification:
Input Voltage: 2S-12S
PCB Cont. Current Rating: 60A
PCB Burst Current Rating: 100A (<60 Sec)
Max Current Sensing: 120A
Output: DC 5.2V & 3A Max
Voltage Divider: 18.182
Amperes per Volt: 36.364
Weight: 20g
Please Note:
- The XT60 Plug and 12AWG wire that are pre-soldered on the board is rating for 30A continuous current and 60A burst current (< 60 Seconds). If a higher current is being used, the plug type and wire size should be changed accordingly. You can refer to this chart for reference.
RGB:
The powerful features of Pixhawk are self-evident. Its integrated RGB full color multifunctional indicator light has high brightness, making it easy to identify flight control status. Compared to previous APMs, it is more intuitive and clear, making it a great design. But the problem lies here: this RGB LED is facing upwards and can only be viewed on the ground, unable to recognize flight control status in the air. Additionally, some racks have a fully enclosed design, such as the SKY-HERO, where the flight control can be hidden between two central boards, making it difficult for users to easily connect USB cables while being well protected. So we referred to the official accessory design and launched this two in one Pixhawk RGB module.
The Pixhawk RGB module has the following characteristics:
·Extend the RGB indicator light to the exterior of the aircraft to display;
·Extend the USB port to facilitate external connection to the USB cable, without being limited by the flight control installation location;
·The Toshiba LED controller and Osram\'s RGB high brightness LED are identical to those on the Pixhawk board;
·Molex original 1.25 connector and HRS original USB socket ensure good contact stability.
M8N GPS:
I2C:
PPM:
Radio telemetry can be used for wireless communication between pixhawk and computer or mobile phone.
PX4FLOW Optical Flow Sensor Smart Camera for PX4 PIXHAWK Flight Control System MB1043
Introduction:
- PX4Flow is an optical flow smart camera. It has a native resolution of 752Ã-480 pixels and calculates optical flow on a 4x binned and cropped area at 250 Hz (bright, outdoors), giving it a very high light sensitivy. Unlike many mouse sensors, it also works indoors and in low outdoor light conditions without the need for an illumination LED at 120 Hz (dark, indoors). It can be freely reprogrammed to do any other basic, efficient low-level computer vision task.
Hardware Specifications:
- STM32F405, 168 MHz Cortex M4F (GFLOPS 128 + 64 KB RAM)
- 752Ã-480 MT9V034 image sensor, L3GD20 3-axis Gyro
- 4 mm M12 lens (IR block filter)
- Size 45.5 mm x 35mm
- Power consumption 115mA / 5V
Package list:
- PX4FLOW Optical Flow Sensor Smart Camera ,MB1043 ultrasonic moudle x 1
- Connecting cable x 1
商品備註・物品狀況:全新・最新關注時間:2026-10-17